Crumbling gravestones covered in moss, faded letters, weathered by rain, wind and ice, a gnarled tree, the cry of an owl in moonlit night; who does not enjoy adding an eerily beautiful atmosphere to a base that will hold a vampire, ghost or necromancer? But how to go about it, what materials can you use and how should you arrange the scene?
Fear not fellow enthusiast of the dark arts, I shall answer these questions in a detailed step-by-step tutorial. In part one I will build a base for a Vampire Lord based on Reaper’s Judas Bloodspire sculpted by Werner Glocke, but naturally you can use the techniques presented below in any project, may it be a scenic base or a gaming board to add a somber, yet unsettling feel to your terrain.
Part II will focus on an objective token using the same techniques, namely a long forgotten shrine with a tumbled over statue and we will also look at generic flagstone bases.
Finally part three will present the painted miniature. We will also add some further details, such as walls and bats.
For starters we have to figure out what kind of graveyard we want to depict and what elements signify the eerie atmosphere we strive for. Throughout history gravestones or monuments for the dead were used by almost all cultures. Roman gravestones were placed outside the cities along roads, so that the passers-by would learn of the deeds of the deceased. In medieval times graveyards would often be placed outside the city or if they where within the city walls they where walled off and could often be found close to a church or chapel. In other cultures the idea of a gravestone or memorial slab is entirely foreign and other forms of commemoration of the dead are used.
Long story short, you have to decide which period of time you want your graveyard to be placed in or if it is a Fantasy project what period of time you would like to reference. The Victorian era provides ample examples for eerie monuments, richly decorated with skulls, skeletons and DEATH himself, while modern tastes are much more reserved. The style of inscriptions will differ, embellishments may be elaborate or simple and finally the age of a gravestone will also affect its condition.
Another thing to consider is, if you want to make your own gravestones or use some commercial headstones. This is up to you, depending on available time and budget. I went for the former, but check out Renedra’s injection plastic offerings and Dark Art’s resin pieces.
As I wanted to fashion a base for a Vampire Lord both medieval and later styles would fit well, depending on what kind of vampire one would like to depict. I decided to go back to the times of Vlad the Impaler (or Vlad Țepeș) who was a Wallachian prince that lived 1428/1431 – 1476/77. Contemporary and later sources describe him as a cruel and ruthless politician, some go so far to paint him as a sadistic monster that reveled in drinking the blood from his impaled enemies. It does not come as a surprise that Bram Stoker got inspired by this historical figure for his Count Dracula novel. A famous portrait of Vlad exists which is apparently based on an original made during his lifetime. An excellent source to base the conversion on.
I had this idea of a fictional family graveyard of the Drăculești, going even further back to the House of Basarab. This would allow to depict weathered gravestones that are a hundred years old, some tumbled over and overgrown, the walls of the graveyard in disrepair. I imagine the entire family to be cursed by the gods with vampirism based on Vlad’s cruelty. Embracing this curse, or ‘gift’ as he likes to refer to it, he may have chosen the graveyard as a resting place. He cares little for its condition and revels in the decay surrounding him.
Accordingly the graveyard should feature:
- Heavily weathered gravestones of various simple designs reminiscent of the period, avoiding a Victorian look.
- Inscriptions or symbols that refer to the family. I thought a dragon would be a fitting choice. While not being the actual arms of the House of Drăculești for this fantasy scenario it would be a pity to not use it.
- A graveyard wall or gate in disrepair, overgrown by ivy and moss. The actual family crest could be placed on the gate.
- Brush, moss, roots and other signs that nature is taking this place back.
Based on the miniature of your choice you will need to decide how to arrange the scene. This depends on the pose, so my suggestions will not always apply to your model, but I try to give some general ideas. Obviously this will influence all aspects of the base and I would recommend to create it while or before you paint the miniature. This way you can test fit and try out different scene arrangements before you get out the crafting materials and commit to a version. If you create the base as an afterthought it may well look disjointed.
In my case the miniature’s original sword was held at such an odd angle that its point was lower than the cast-on base. Instead of cutting off the arm and adjusting the weapon I kept the angle and decided to put the miniature on the edge of some stone steps. This works also very well with his raised knee and outstretched left arm.
Accordingly if your miniature has an odd pose or would really benefit from being put on an elevation do not hesitate to make the base conform to your miniature. If you need to alter your initial ideas for the scenic base this may be frustrating, but your miniature will fit much better in the scene and you will not run in the problem that the pose looks odd or the miniature looks unbalanced.
In the end I decided to replace his long sword with a Hungarian sabre or szabla, which I carved from a two-handed sword that was part of the Northstar plastic gnolls set using a scalpel. The historical Vlad Țepeș would most likely have used an european style sword, but his immortal counterpart may have adopted a saber when it became more acceptable among the nobility a hundred years after his “death”. Excuse me, you said something? Ascension? Ok, vampire Vlad, lets call it ascension then *rolls eyes*.
The size of the miniature will also dictate how much of a graveyard you can depict. In my case the elaborate cloak did ask for a large base (6 cm diameter), so did the integration of some steps. If you have only a small skeleton or ghoul to base just add the essence of the scene to the base. The obvious choice for a graveyard is a gravestone or memorial slab. Why not place the miniature on a tumbled over gravestone or perched on a monument? The size of the base should not limit your creativity, rather get inspired by the pose and size of the miniature and break the scene down to its most basic elements that really bring across an eerie feeling.
Finally some framing devises for your scene may be a good idea. This is especially true if it is a large creature base. Think of the base as a three-dimensional photograph. What is happening in the background, what in the foreground? Is there something on the left and/or right to frame your miniature? What kind of story do you want to tell with your piece?
I came up with the following scene arrangement:
- Foreground: Steps leading up to the entrance of the graveyard, flanked by gravestones and a rock face.
- Midground: Vlad framed by gravestones to the left and a small tree to the right. The small tree could feature a bat hanging from it, the gravestones to the left could feature bats flying past them.
- Background: Part of the ruined graveyard wall and a bat swarm flying through the ruined archway.
With such a scene arrangement we should achieve a visually pleasing composition that is framed to three sides, focusing the gaze on Vlad. The bats in the background are a nice theming element and work well with the outstretched arm and pointing finger: “Fly my pretties! Fly!”
Provisions for your crafting adventure
- Sharp implements: A scalpel and a needle tool to carve rock faces and the stairs
- Paint brushes of various sizes to apply paint and wood glue, but also to drybrush.
- Wire brushes (steel and brass) to add texture to the rock faces.
- Sculpting tools to shape greenstuff and XPS. A ball tool and colour shaper is a good start.
- Some bunched up tin foil to add a rock texture to the XPS.
- Dremel to bevel the MDF base (optional). If you don’t have one some coarse and fine sanding paper will also do.
- An airbrush or sprayer bottle to apply a fixative (e. g. matte medium) to the finished piece.
- A palette knife to spread out wood filler.
- Wood glue.
- Super glue. I use Insta Cure+ by Avetek.
- AK Interactive Sand and Gravel fixer (optional). Thinned acrylic medium with a bit of flow release will also do.
- Styrofoam glue. Be careful here to choose an appropriate product, as many glues react with styrofoam and dissolve it. I use Selleys Liquid Nails Fast.
For the groundwork, stairs, rock faces and gravestones:
- A circular or rectangular base. Really depends on your system of choice or your preference. I used some laser-cut 3mm MDF this time as I would build up the base and thus did not worry too much about thickness. Alternatively you can use 1mm polystyrene, cork or other materials. Just make sure they don’t warp.
- Shellac to seal the MDF and to prevent warping.
- Extruded polystyrene (XPS). That is the dense stuff for construction, not the crumbly stuff you use as packaging.
- Wood filler. Either ready-made or as powder. I use Bostik Fill-and-Fix. We will use this to add texture to the stairs and gravestones, but also to depict rock faces.
- Finely sieved soil from your garden or backyard. Can be any colour, but a darker brown-grey works well for a graveyard. Different pigments ranging from dark brown to light brown. Either bought or simply soil you collected so that we can add some variation to the dark soil.
- Small cork pieces to depict larger rocks.
- Craft paints (browns, grays, black) to paint the stairs.
- Vallejo Smoke to add contrast to the stone if necessary (optional).
- Matte varnish to mix with pigment and water to fashion a brown wash for the stone.
- AK Interactive Grime/Slime effect paint to depict light moss (optional).
Vegetation: Moss, ivy, small gnarly tree, mushrooms:
- MiniNatur grass tufts, ivy and autumn birch foliage nets (optional). I used a selection of autumn and summer grass tufts. You can use any tufts you have at hand and also clump foliage. The ivy can be depicted using birch seed pods, too ( a sweet tut by Zaboobadiboo hiding behind the link). Whatever floats your boat.
- Matte spray varnish to reduce the shine of the grass tufts and foliage. I use Testor’s Dull Coat.
- Brown acrylic spray paint to slightly darken the tufts or alternatively a brown wash to dull the shine of the tufts and grass.
- Thin wire to make an armature for the tree.
- Brown-grey craft paint to paint the tree.
- AK Interactive Grime/Slime effect paint to depict light moss on the bark (optional).
- Acrylic caulking as a first layer followed by wood filler to depict the bark.
- Fine turf e .g. Woodland Scenics range of fine turf in dark green or any other fine turf. This is basically very finely ground colored foam. We will use this to depict moss.
- Dark or medium green, yellow and beige acrylic paint and Vallejo Umber wash. We will use this to add depth to the moss.
- Dried basil to depict fallen leaves.
- Assortment of dry tea to depict roots and leaves.
- Some singular leaves from the MiniNatur foliage nets (optional).
- Small snake. The Busch Kleintierset is your friend.
- Lizard. Same here.
- Bats. Reaper has a bat swarm as well as a single bat in one of its familiar sets. The quality of the Bones versions is bad to average, so go for metal if you can. If it is for background effects only consider the Bones version, as it is half the price.
Let’s get down to the nitty-gritty!
- Cut the MDF to size or if you use laser-cut shapes make sure the piece of MDF you are using is not warped. Bevel the edges of the MDF if you desire. I did this only later to make it easier to integrate the rock faces, however, without a Dremel this is very hard to do, so you are better off doing this in the beginning, if you only have sanding paper.
- Apply a protective coat of Shellac. This will seal the MDF and prevent warping. I always use this when working with MDF and so far I had no problem with warping caused by moisture. Still look out for warping caused by mechanical stress, especially if you want to make a bigger base or gaming board.
- Take a small piece of XPS and rough out the shape of the stairs and rock faces. Don’t overthink this step. Just combine whatever XPS you have lying around until you achieve a pleasing result. You can temporarily fixate the foam with toothpicks and cut it to shape. If you want to add a tree and make it an integral part of the base you can already twist an armature and glue it to the base. Alternatively you can also magnetize the tree, so that you can remove and exchange it (see my hill tutorial to get an idea how to magnetize the base).
- When you are happy use some styrofoam glue to fixate the XPS.
- While this is drying cut some gravestone shapes out of the XPS using a sharp scalpel.
- Use a needle tool or fine pen to inscribe weathered adornments, inscriptions or symbols. The results will be better if you score the shape first with the scalpel and only then widen it with the needle tool. This will prevent the XPS to develop fine fissures.
- Keep in mind that any designs inscribed in the XPS will not be very sharp. This is perfect to depict weathered stone, but if you want the gravestones to be newer I would recommend to make them out of greenstuff or to add a layer of greenstuff to the XPS and inscribe letters or symbols with a lubricated needle tool.
- Now it is time to coat the headstones, stairs and rock faces with some thinned down wood filler to add a stone texture. You can also use the bunched up tin foil and roll it over the XPS to add even more texture. The rock faces need a thicker mix, as you will carve them further.
- Now cover any remaining surfaces and the tree armature with some thinned down acrylic caulking.
- After this is all dry we focus on the rock faces. The dry wood filler can be carved using a needle tool and textured using wire brushes. This will produce a more naturalistic rock texture.
- While you have some wood filler ready cover the tree trunk and carve a bark texture into the dry filler. For inspiration check out this tutorial on all kinds of trees.
- Onwards to painting all the stone surfaces. I use some brown-grey as a basecoat, drybrush with succeeding amounts of beige mixed in the base color and finish off with a mixture of brown pigment, matte varnish and water (a sprinkle of pigment to 1 part varnish, 2 parts water). You can drybrush a last time if you feel it is all too dark now, but that is up to you.
- If you did not already do so, bevel the edge of the MDF, shellac it and cover with acrylic caulking. I already extended the rock faces over the rim of the base, so I won’t need to add anything or paint them again. This is optional and you can do it first if you feel you could destroy some of the detail while sanding.
- Now it is time to paint the ground brown to prepare it for the next step and paint any remaining rocks. You can also start painting the bark. A brown-grey with some beige highlights works well for a generic tree. You can also use some AK Interactive Grime/Slime effect paint to add a light moss effect. Apply it to the stairs or the tree with a brush and thin it on the model with some odorless thinner.
- The main reason to paint the ground is to avoid white sections showing through the soil, which we will apply to the piece now. Apply wood glue to the areas that will show soil, then dust on fine soil from your garden. You read right, nothing beats soil to depict soil! Let dry and carefully remove any excess.
- Using either Ak Gravel and Sand Fixer or some matte medium (about 10 parts water, 1 part medium and a drop of flow release) to fixate any remaining loose soil. You can also add some lighter shades of soil and coarser sand to add variation.
- Now you can apply some more moss growth using a “moss paste”. This is entirely optional, depending what kind of moss you want to depict. Mix fine turf, green acrylic paint, wood glue and water to a paste. It needs to be sticky enough to adhere to the stone, but also easy to spread. Don’t worry if the paste looks bright green, it will darken quite a bit when the wood glue tries. With a toothpick (a brush is not very suitable for this kind of work) take some of the paste and apply wherever you would like to add some moss. Now spread the paste with the toothpick and press it down.
- After the paste is dry add a brown wash and drybrush with yellow to highlight it.
- Finally we get to add some tufts, foliage and fallen leaves! This is always the exciting part, as everything comes together. Place tufts to your heart’s content using super glue and fixate single leaves, made of dry basil, tea or from MiniNatur nets with thinned down wood glue. Add foliage to the tree and fixate with super glue. I went for autumn birch tree nets by MiniNatur, but you can use fine turf or clump foliage. In these cases use some filter wool as a substructure.
- To finish the piece we apply either by hand brush or with an airbrush some brown wash to fuse it all together and to tone down the lustre of the tufts. This is followed by a fine misting with thinned down acrylic medium (10 parts water, 1 part medium, one drop flow release).
- But wait there is more! Shrooms! Fashion some mushrooms out of greenstuff and wire. Put the wire stem in some left over XPS, add a mushroom head with greenstuff, let cure and then coat the whole thing with acrylic medium. I got some good results covering the stem with liquid greenstuff, but the medium will do fine. To be honest, so far that is the best use I found for the liquid greenstuff.
- Paint the mushrooms up and drill some holes in the base to secure them. Glue them in the holes with super glue.
There we go! We have a nice graveyard themed base that needs only a few additions and it will fit Vampire Vlad quite well:
- As you can see the gap on the base will fit the graveyard wall. I think I will use a magnet to attach it to simplify transport.
- I also need to add the bat swarm to the background and another gravestone to the front left. This one was the bottom part of the bat swarm. I cut the Bones version in two pieces to be able to mount the swarm on some clear acrylic rod. Given the gravestone had a skull with batwings on it…*cough* I decided to add some new design with greenstuff. I had a flying dragon in mind to mirror the headstone behind it.
- I also want to add another hanging bat to the lower branch of the tree. This will most likely be the bat from the Reaper familiar set.
- A nice touch could be a tumbled over statuette that was originally placed in the little alcove of the gravestone on the front right. I’ll see what my greenstuff skills can produce.
Until next time and always wield your brush with honor!
If you would like a constantly updated, themed PDF terrain building, painting and roleplaying guide consider supporting me on Patreon. There also other choice rewards for supporters.
If you are not keen on Patreon, but enjoy my content and would like to see me well caffeinated so that I can publish tutorials, reviews and guides more frequently click below and buy me cup of dark, mellow goodness.